How to fix mouse lag or stuttering in Windows 10?
Jun 30, 2025 pm 04:03 PM
Mouse lag or delay can be resolved by checking hardware connections, updating drivers, adjusting system settings, and excluding software conflicts. First check the battery level of the wireless mouse, replace the USB interface, clean the sensor and disable the touchpad; secondly update or roll back the mouse driver through the device manager; then cancel the energy-saving settings of the USB device and adjust the mouse pointer speed; finally enter the clean boot mode to troubleshoot third-party software interference. Checking one by one in order usually solves the problem.
It is really annoying to have mouse lag or occasional delays on Windows 10, especially when working or playing games. This situation is not necessarily due to the hardware failure, but is often caused by system setup, driver or connection problems. The following methods can help you troubleshoot and solve this problem.
Check the mouse hardware and connections
First, you have to confirm whether it is a problem with the mouse itself. If you are using a wireless mouse, first check if the battery is about to run out of power. Low battery will cause the signal to be unstable and thus stutter. If it is a wired mouse, try to plug in the USB port. Sometimes the interface is not powered enough and it will cause slow response.
- Change the mouse to another computer to see if there are any problems
- If it is a wireless mouse, use it close to the receiver to avoid obstacles in the middle
- Clean the sensor at the bottom of the mouse, dust may also affect the tracking effect
Especially for laptop users, sometimes the trackpad and external mouse work at the same time may also cause conflicts. You can try to disable the trackpad to see if there is any improvement.
Update or rollback the mouse driver
Outdated or damaged mouse drivers can also lead to poor operation. You can check the current driver status through the Device Manager.
- Open Device Manager → Expand "Mouse and Other Pointer Devices"
- Right-click on your mouse device (such as HID-compliant mouse) → select "Update Driver"
- If you have problems after recently updating the driver, you can try "rollback the driver"
In addition, you can also download the latest official driver installation on the mouse official website, especially peripherals of brands such as Logitech and Razer. The built-in driver software can often provide better compatibility.
Adjust system settings and power management
Power management of Windows can sometimes limit the performance of USB devices to save power, which can also cause wireless mouse stuttering.
- Open Device Manager → Find “Universal Serial Bus Controller”
- Right-click each “USB Root Hub” → select “Properties”
- Switch to the Power Management tab → Uncheck "Allow the computer to turn off this device to save power"
In addition, it is also helpful to adjust the movement speed of the mouse pointer in the control panel. Some people adjust the "feel" too fast or too slow, which will affect the response. You can adjust it appropriately in "Mouse Settings" and turn off the option "Improve pointer accuracy" as some users report that it will cause slight delays.
Exclude software conflicts and background occupations
Some third-party software, such as antivirus software, system optimization tools and even Steam clients, may also interfere with the normal operation of the mouse. You can try to enter "clean boot" mode (only load the most basic system services) to see if the problem still exists.
- Press Win R to enter
msconfig→ Switch to the "Services" tab - Check "Hide all Microsoft services" → Click "Disable all"
- Switch to the "Startup" tab again → Use Task Manager to disable all startup items
If the mouse no longer stutters at this time, it means that there is a problem with a third-party software and you can check it one by one.
Basically these common troubleshooting methods. In many cases, it is not caused by the mouse being broken, but by the small problems in the settings or environment. If you encounter a mouse stutter, don’t rush to change the device. Check it out from these aspects first, maybe it will be done.
The above is the detailed content of How to fix mouse lag or stuttering in Windows 10?. For more information, please follow other related articles on the PHP Chinese website!
Hot AI Tools
Undress AI Tool
Undress images for free
Undresser.AI Undress
AI-powered app for creating realistic nude photos
AI Clothes Remover
Online AI tool for removing clothes from photos.
Clothoff.io
AI clothes remover
Video Face Swap
Swap faces in any video effortlessly with our completely free AI face swap tool!
Hot Article
Hot Tools
Notepad++7.3.1
Easy-to-use and free code editor
SublimeText3 Chinese version
Chinese version, very easy to use
Zend Studio 13.0.1
Powerful PHP integrated development environment
Dreamweaver CS6
Visual web development tools
SublimeText3 Mac version
God-level code editing software (SublimeText3)
Windows Security is blank or not showing options
Jul 07, 2025 am 02:40 AM
When the Windows Security Center is blank or the function is missing, you can follow the following steps to check: 1. Confirm whether the system version supports full functions, some functions of the Home Edition are limited, and the Professional Edition and above are more complete; 2. Restart the SecurityHealthService service to ensure that its startup type is set to automatic; 3. Check and uninstall third-party security software that may conflict; 4. Run the sfc/scannow and DISM commands to repair system files; 5. Try to reset or reinstall the Windows Security Center application, and contact Microsoft support if necessary.
Windows stuck on 'undoing changes made to your computer'
Jul 05, 2025 am 02:51 AM
The computer is stuck in the "Undo Changes made to the computer" interface, which is a common problem after the Windows update fails. It is usually caused by the stuck rollback process and cannot enter the system normally. 1. First of all, you should wait patiently for a long enough time, especially after restarting, it may take more than 30 minutes to complete the rollback, and observe the hard disk light to determine whether it is still running. 2. If there is no progress for a long time, you can force shut down and enter the recovery environment (WinRE) multiple times, and try to start repair or system restore. 3. After entering safe mode, you can uninstall the most recent update records through the control panel. 4. Use the command prompt to execute the bootrec command in the recovery environment to repair the boot file, or run sfc/scannow to check the system file. 5. The last method is to use the "Reset this computer" function
Proven Ways for Microsoft Teams Error 657rx in Windows 11/10
Jul 07, 2025 pm 12:25 PM
Encountering something went wrong 657rx can be frustrating when you log in to Microsoft Teams or Outlook. In this article on MiniTool, we will explore how to fix the Outlook/Microsoft Teams error 657rx so you can get your workflow back on track.Quick
The RPC server is unavailable Windows
Jul 06, 2025 am 12:07 AM
When encountering the "RPCserverisunavailable" problem, first confirm whether it is a local service exception or a network configuration problem. 1. Check and start the RPC service to ensure that its startup type is automatic. If it cannot be started, check the event log; 2. Check the network connection and firewall settings, test the firewall to turn off the firewall, check DNS resolution and network connectivity; 3. Run the sfc/scannow and DISM commands to repair the system files; 4. Check the group policy and domain controller status in the domain environment, and contact the IT department to assist in the processing. Gradually check it in sequence to locate and solve the problem.
the default gateway is not available Windows
Jul 08, 2025 am 02:21 AM
When you encounter the "DefaultGatewayisNotAvailable" prompt, it means that the computer cannot connect to the router or does not obtain the network address correctly. 1. First, restart the router and computer, wait for the router to fully start before trying to connect; 2. Check whether the IP address is set to automatically obtain, enter the network attribute to ensure that "Automatically obtain IP address" and "Automatically obtain DNS server address" are selected; 3. Run ipconfig/release and ipconfig/renew through the command prompt to release and re-acquire the IP address, and execute the netsh command to reset the network components if necessary; 4. Check the wireless network card driver, update or reinstall the driver to ensure that it works normally.
How to fix 'SYSTEM_SERVICE_EXCEPTION' stop code in Windows
Jul 09, 2025 am 02:56 AM
When encountering the "SYSTEM_SERVICE_EXCEPTION" blue screen error, you do not need to reinstall the system or replace the hardware immediately. You can follow the following steps to check: 1. Update or roll back hardware drivers such as graphics cards, especially recently updated drivers; 2. Uninstall third-party antivirus software or system tools, and use WindowsDefender or well-known brand products to replace them; 3. Run sfc/scannow and DISM commands as administrator to repair system files; 4. Check memory problems, restore the default frequency and re-plug and unplug the memory stick, and use Windows memory diagnostic tools to detect. In most cases, the driver and software problems can be solved first.
Windows 11 KB5062660 24H2 out with features, direct download links for offline installer (.msu)
Jul 23, 2025 am 09:43 AM
Windows 11 KB5062660 is now rolling out as an optional update for Windows 11 24H2 with a few new features, including Recall AI in Europe. This patch is available via Windows Update, but Microsoft has also posted direct download l
How to repair Windows 11 using command prompt
Jul 05, 2025 am 02:59 AM
How to use command prompt to repair Windows 11? 1. Enter the command prompt through the recovery environment: enter the recovery environment through USB boot or three consecutive interrupts, and then select Troubleshooting > Advanced Options > Command Prompt; 2. Use DISM to repair the system image: Run DISM/Online/Cleanup-Image/CheckHealth to check for corruption, DISM/Online/Cleanup-Image/ScanHealth scanning problem, DISM/Online/Cleanup-Image/RestoreHealth to repair the problem, and specify an external source if necessary; 3. Run SF
